SWIFTPOXY **FAST SET** (QUART KIT)
SWIFTPOXY (32 OZ QUART KIT)
****SWIFTPOXY CAN NOT BE SHIPPED THROUGH USPS. PLEASE CHANGE P.O. BOX ADDRESSES TO A PHYSICAL STREET ADDRESS SO YOUR ORDER ISN'T DELAYED****CAN NOT BE SHIPPED OVERSEAS OR BY AIRPLANE.****
DRY TO TOUCH IN 5 HOURS OR LESS
**DO NOT SAND OR APPLY ANY DECALS, VINYL, OR WATERSLIDES UNTIL THE FULL 5 HOURS HAS PASSED**
NEXT LAYER CAN BE APPLIED IN AS LITTLE AS 2 HOURS
32 TOTAL OUNCES
16 OZ OF PART A
16 OZ OF PART B
MEASURE 1:1 RATIO
MIX SWIFTPOXY FOR 5 mins (Mix aggressive. The only time you want to stir slower and longer then allow to sit for bubbles to rise to pop them is if you’re doing clear molds.)
Apply immediately (DO NOT ALLOW TO SIT IN MIXING CUP DUE TO QUICK WORK TIME UNLESS YOU'RE DOING CLEAR MOLDS, then please refer to the mold directions below.)
Use gloved finger to work bubbles out before reaching for any heat, if done properly you’ll need little to no heat.
Once layer is to your liking hit with heat one to two rotations.
Sand and Apply next layer at 5 hours, or apply decals, vinyl, etc.
Molds will be rock hard at 5 hours or less.
MEASURE 1:1 ratio
Mix for 5 mins. (Mix AGGRESSIVELY. The only time you want to stir slower and longer then allow to sit for bubbles to rise to pop them is if you’re doing clear molds.)
Add coloring/glitter (remember coloring to epoxy ratio of 10% or less to not mess up chemical reaction and cause molds to always be bendy or the need to allow them to cure longer to get hard)
(IF DOING CLEAR MOLDS WITH SWIFTPOXY: PLEASE STIR SLOW BEFORE POURING MIXTURE INTO YOUR MOLD. Because Swiftpoxy is a fast set epoxy, it begins to thicken and set up as you stir. Thickening will trap bubbles and you will not be able to remove them from the mold once poured like you can from a thinner layer on tumbler.)
Pour into silicone mold, then allow bubbles to rise to the top before spritzing with alcohol.
(Spritz top of mold pieces with alcohol as heat will break down silicone molds quickly and eventually.)
Must mix aggressively for 5 mins.
Work time 15-20 mins
Dry to touch in 5 hours or less
CAN APPLY ANOTHER LAYER between 3-4.5 hours IF you’re 100% sure you measured and mixed properly, layer at this point will be tacky. Ideally, you want to either sand or apply next layer when bottom layer is tacky to ensure both layers create a chemical or mechanical bond. This helps with durable if tumbler is accidentally dropped.
ALLOW TO CURE a minimum of 72 hours after last layer in-order to meet the FDA Compliance Standards of being food safe.
**If Tumbler layer is tacky after 5 hours either SWIFTPOXY wasn’t measured properly or it wasn’t stirred a full 5 mins. Beth has personally tested this and 5 mins. is the magic number** MUST STIR AGGRESSIVELY FOR 5 mins.
Work and storing temperatures: 50-75 degrees F
**Hotter temps will cause SWIFTPOXY to dry faster, colder temps will cause SWIFTPOXY to dry slower.**
Opened (heat seal under lid popped) AND NOT stored at recommended storing temps. SWIFTPOXY will not work properly period.
Unopened AND stored at recommended storing temps. SWIFTPOXY will work properly for a year or more.
Caution: Eye and Skin irritant. Do not swallow. Do not get in eyes. Do not get on skin or clothing. Do not breathe fumes. Use proper PPE at all times. KEEP OUT OF REACH OF CHILDREN.