Swiftpoxy (Thin fast set) Choose your size kit:

CAN NOT SHIP AIR OR WATER, UPS AIR NEXT DAY OR THROUGH USPS PER  TRANSPORTATION OF PACKAGES PER OSHA REGULATIONS. UPS GROUND OR UPS 3-DAY SELECT (extra)

Free shipping in the upper contiguous 48 USA.

NO PO BOX ADDRESSES ALLOWED AND CAN NOT SHIP VIA USPS MUST HAVE A PHYSICAL ADDRESS AS YOUR SHIPPING ADDRESS OR ORDER WILL BE CANCELLED

Tumblerpoxy 2.0 & Swiftpoxy both incorporate 2 light stabilizers: The UV Light Stabilizer and the HALS ( or Hindered Amine Light Stabilizer.) The UV Stabilizer is in there to take care of most of the damaging affects that happens from UV light (SUN RAYS). However, it doesn’t do a great job protecting against yellowing so for double the protection Hindered Amine Light Stabilizer is added to target the yellowing because it interrupts the yellowing at the outset, making it much more unlikely to happen. The “purple” hue is simply there in the bottle to make our product look more appealing to the naked eye because without the light purple, it would look yellow in the bottle from the very beginning as all epoxy part B starts yellow. (due to the HALS because this chemical is yellow itself) when a customer receives it, so we made it a pretty light purple/blue color. 

Double the light stabilizers equals better protection for your artwork!

Formulated
Specifically for use
On all layers: even top &
Final coats. Whites and light
Colors as well!

FAST SET EPOXY  

 SWIFTPOXY has our new state of the art UV resistant technology which makes it THE BEST fast set on the market!

Perfect for all layers including topcoats and on white tumblers and artwork. 

PLEASE STORE ALL EPOXIES IN YOUR CLIMATE CONTROLLED HOME. Any epoxy that gets too cold (frozen) or too hot WILL NOT WORK PROPERLY! DO NOT STORE EPOXY IN YOUR GARAGE.

SWIFTPOXY: is a fast set so it requires being stored and used in temperatures of 75° or higher for best results. 

FAST SET

****SWIFTPOXY CAN NOT BE SHIPPED THROUGH USPS. PLEASE CHANGE P.O. BOX ADDRESSES TO A PHYSICAL STREET ADDRESS SO YOUR ORDER ISN'T DELAYED****CAN NOT BE SHIPPED OVERSEAS OR BY AIRPLANE. ****

DRY TO TOUCH IN 2-3 HOURS

**DO NOT SAND OR APPLY ANY DECALS, VINYL, OR WATERSLIDES UNTIL THE FULL 2-3 HAS PASSED**

NEXT LAYER CAN BE APPLIED IN AS LITTLE AS 2 HOURS 

1:1 Ratio

10-15 min work time

Dry to touch in 2-3 hours

400-500 degree heat resistant 

FDA Complaint once food safe once fully cured a minimum of 72 hours

Let come to room temperature before using right after delivery. Cold weather makes all epoxies thicker so a longer stir time is required. Room temperature that works great for SWIFTPOXY is 72°-76°

⭐️All of our epoxies are proudly made here in the U.S.A.⭐️

 **TUMBLER DIRECTIONS** 

MEASURE 1:1 RATIO

MIX SWIFTPOXY FOR 5 mins. AGGRESSIVELY or until epoxy is clear. Mixing slow or in colder environments, will require the epoxy needing to be stirred longer. In order to get non-tacky cups every time, make sure there’s no ceiling fans, heaters, dehumidifiers, floor fans, etc. blowing on your wet epoxy. Air flowing directly on your wet epoxy will not allow our epoxy to heat up like it needs to to dry properly. This is a fast-setting epoxy, so it needs to heat up quickly. 

Apply immediately 

Use gloved finger to work bubbles out before reaching for any heat, if done properly you’ll need little to no heat.

Once layer is to your liking hit with heat one to two rotations.

If working from a bigger batch of epoxy, make sure you’re stirring for few seconds between projects. Stuff settles and if not stirred periodically between tumblers, some tumblers will dry properly, and others won’t from the same batch.

Sand and apply next layer as early as 2-5 hours but depending on room temperature, or applying decals, vinyl, etc., you may have to wait 8 hours.

 GLITTER MOLDS:

Molds will be rock hard at 5 hours or less.

MEASURE 1:1 ratio

Mix for 5 mins. or until epoxy is clear: no stringiness or fogginess (Mix aggressive. The only time you want to stir slower and longer then allow to sit for bubbles to rise to pop them is if you’re doing clear molds.)

Add coloring/glitter (remember coloring to epoxy ratio of 10% or less to not mess up chemical reaction and cause molds to always be bendy or the need to allow them to cure longer to get hard)

(IF DOING CLEAR MOLDS WITH SWIFTPOXY: PLEASE STIR SLOW and for 7 mins. BEFORE POURING MIXTURE INTO YOUR MOLD. Because Swiftpoxy is a fast set epoxy, it begins to thicken and set up as you stir. Thickening will trap bubbles and you will not be able to remove them from the mold once poured like you can from a thinner layer on tumbler.)

Pour into silicone mold, then allow bubbles to rise to the top before spritzing with alcohol.

(Spritz top of mold pieces with alcohol as heat will break down silicone molds quickly and eventually.)

*QUICK TIPS*

Must mix aggressively for 5 mins. or until epoxy is clear with NO stringiness or fogginess.

Work time 15-20 mins

Dry to touch in 5 hours or less

CAN APPLY ANOTHER LAYER between 3-4.5 hours IF you’re 100% sure you measured and mixed properly, layer at this point will be tacky. Ideally, you want to either sand or apply next layer when bottom layer is tacky to ensure both layers create a chemical or mechanical bond. This helps with durable if tumbler is accidentally dropped.

ALLOW TO CURE a minimum of 72 hours after last layer in-order to meet the FDA Compliance Standards of being food safe.

**If Tumbler layer is tacky after 5 hours either SWIFTPOXY wasn’t measured properly, work room temperature wasn’t 75° degrees or higher, or it wasn’t stirred a full 5 mins. or longer if epoxy is cold (all epoxy thickens when cold) MUST STIR AGGRESSIVELY FOR 5 mins or longer.

Work and storing temperatures

75°F or higher

**Hotter temps will cause SWIFTPOXY to dry faster, colder temps will cause SWIFTPOXY to dry slow**

***NO REFUNDS AND NO RETURNS. Please refer to our return policy located at the bottom of this website.

PLEASE CONSIDER PURCHASING THE EXTRA ROUTE SHIPPING INSURANCE WE OFFER TO GUARANTEE IF ORDER IS LOST OR DAMAGED, ORDER WILL BE REPLACED QUICKLY.***

 Caution: Eye and Skin irritant. Do not swallow. Do not get in eyes. Do not get on skin or clothing. Do not breathe fumes. Use proper PPE at all times. KEEP OUT OF REACH OF CHILDREN.