Skip to product information
1 of 1

Tumblerpoxy

The Original Tumblerpoxy TPOG Choose your size kit:

The Original Tumblerpoxy TPOG Choose your size kit:

Regular price $68.26 CAD
Regular price Sale price $68.26 CAD
Sale Sold out
Tax included. Shipping calculated at checkout.
Size
×

We often restock popular items or they may be returned by the other customers. If you would like to be notified when this happens just enter your details below.


The Original Tumblerpoxy TPOG Choose your size kit:

Please select variant
Please enter name
Invalid email address
Required mobile number Invalid number Invalid country code Too short Too long ✓ Valid
Your notification has been registered. Close
Looks like you already have notifications active for this size!

We respect your privacy and don't share your email with anybody.

×

We have cancelled your request.


Regular TUMBLERPOXY CAN SHIP WORLDWIDE! Free shipping in the USA including Hawaii, Alaska, and Puerto Rico! 


***NEW & IMPROVED with more UV inhibitors for a regular epoxy.***


(Regular Epoxy)

TUMBLERPOXY now has MORE UV inhibitors which help prolong the sun from yellowing epoxy projects! Not recommended for white or light colored items as TUMBLERPOXY only has the regular UV inhibitors as other epoxy brands. Swiftpoxy and 2.0 have a higher more advance UV protection recommended for these types of items.

We do not recommend leaving ANY projects made with any epoxy in the direct sun or extremely hot areas for long periods of time because they will yellow.

Tumblerpoxy is not a deep pour epoxy so projects done in layers deeper than 1/2” will flash cure and yellow immediately.

 

PLEASE STORE ALL EPOXIES IN YOUR CLIMATE CONTROLLED HOME. Any epoxy that gets too cold (frozen) or too hot WILL NOT WORK PROPERLY! DO NOT STORE EPOXY IN YOUR GARAGE.

1 GALLON KIT= total kit volume

  • 30-35 minute work time
  • Dry to touch in 8-12 hours depending on room temperature
  • 1:1 RATIO
  • 400-500 degree heat resistance 
  • FDA Compliant food safe once fully cured a minimum of 72 hours after last application.

⭐️All of our epoxies are proudly made here in the U.S.A.⭐️

 **TUMBLER DIRECTIONS**

MEASURE 1:1 RATIO

MIX TUMBLERPOXY FOR 3 mins.

Apply immediately 

Use gloved finger to work bubbles out before reaching for any heat, if done properly you’ll need little to no heat.

Once layer is to your liking hit with heat one to two rotations.

Sand and apply next layer at about 12 to 18 hours depending on room temperature, or apply decals, vinyl, etc.

**MOLD DIRECTIONS**

Mold pieces will be bendy after 8-12 hours drying in the mold. Remove from mold and allow to finish curing on a flat surface for 3-5 days. Mold pieces can be left in mold until fully cured but Beth has found they harden and cure faster outside the mold. Also, removing them earlier helps you be able to use mold again quicker. If mold pieces don’t harden up after 3-5 days and remain bendy, either measurements were off, mixture wasn’t stirred long enough or coloring to epoxy ratio of 10% or less wasn’t followed...chemical reaction between part A and Part B was interrupted.

MEASURE 1:1 ratio

Mix for 3 mins.

Add coloring/glitter (remember coloring to epoxy ratio of 10% or less to not mess up chemical reaction and cause molds to always be bendy or the need to allow them to cure longer to get hard)

(IF DOING CLEAR MOLDS WITH TUMBLERPOXY: PLEASE STIR SLOW BEFORE POURING MIXTURE INTO YOUR MOLD.)

Pour into silicone mold, then allow bubbles to rise to the top 5-8 mins. before spritzing with alcohol.

(Spritz top of mold pieces with alcohol as heat will break down silicone molds quickly and eventually.)

*QUICK TIPS*

Must mix 3 mins.

Work time 30-35 mins

Dry to touch in 12-18 hours depending on room temperature 

CAN APPLY ANOTHER LAYER between 6-8 hours IF you’re 100% sure you measured and mixed properly. Bottom layer at this point will be tacky. Ideally, you want to either sand or apply next layer when bottom layer is tacky to ensure both layers create a chemical or mechanical bond. This helps with durability if tumbler is accidentally dropped.

ALLOW TO CURE a minimum of 72 hours after last layer in-order to meet the FDA Compliancy Standards of being food safe.

**If Tumbler layer is tacky after 12-18 hours either TUMBLERPOXY wasn’t measured properly, or it wasn’t stirred a full 3 mins. Beth has personally tested this and 3 mins. is the magic number**

Work and storing temperatures:

50-75 degrees F

**Hotter temps will cause TUMBLERPOXY to dry faster, colder temps will cause TUMBLERPOXY to dry slower. **

Opened (heat seal under lid popped) TUMBLERPOXY will work properly for less than a year.

Unopened TUMBLERPOXY stored at recommended storing temps will work properly for over a year.

 

***NO REFUNDS AND NO RETURNS***

 Caution: Eye and Skin irritant. Do not swallow. Do not get in eyes. Do not get on skin or clothing. Do not breathe fumes. Use proper PPE at all times. KEEP OUT OF REACH OF CHILDREN. 

View full details

Customer Reviews

Based on 29 reviews
100%
(29)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
M
Marie

Great product great customer service

G
Guy

Works great and fast shipping

S
Susanna

The Best epoxy on the market!

M
Michael

Excellent as always

M
Mary

Love this stuff