2.0 Tumblerpoxy (Thick fast set) Choose your size kit:

CAN NOT SHIP AIR OR WATER, UPS AIR NEXT DAY, OR THROUGH USPS PER TRANSPORTATION OF PACKAGES PER OSHA REGULATIONS. UPS GROUND OR UPS 3-DAY SELECT (extra)

NO PO BOX ADDRESSES ALLOWED AND CAN NOT SHIP VIA USPS MUST HAVE A PHYSICAL ADDRESS AS YOUR SHIPPING ADDRESS OR ORDER WILL BE CANCELLED

Tumblerpoxy 2.0 & Swiftpoxy both incorporate 2 light stabilizers: The UV Light Stabilizer and the HALS ( or Hindered Amine Light Stabilizer.) The UV Stabilizer is in there to take care of most of the damaging affects that happens from UV light (SUN RAYS). However, it doesn’t do a great job protecting against yellowing so for double the protection Hindered Amine Light Stabilizer is added to target the yellowing because it interrupts the yellowing at the outset, making it much more unlikely to happen. The “purple” hue is simply there in the bottle to make our product look more appealing to the naked eye because without the light purple, it would look yellow in the bottle from the very beginning as all epoxy part B starts yellow. (due to the HALS because this chemical is yellow itself) when a customer receives it, so we made it a pretty light purple/blue color. 

Double the light stabilizers equals better protection for your artwork!

Formulated
Specifically for use
On all layers: even top &
Final coats. Whites and light
Colors as well!

Fast-set type Epoxy

THICK THICK THICK ESPECIALLY WHEN COLD. Let come to room temperature before using right after delivery. During cold weather months please mix for 5-8 mins because it’s so thick. Cold weather makes all epoxies thicker so a longer stir time is required. Room temperature that works great for 2.0 is 75°-80°

10/10 UV Protection!

The BEST UV protection you can get in an epoxy!

Perfect for all layers including topcoats and on white tumblers and artwork. 

PLEASE STORE ALL EPOXIES IN YOUR CLIMATE CONTROLLED HOME. Any epoxy that gets too cold (frozen) or too hot WILL NOT WORK PROPERLY! DO NOT STORE EPOXY IN YOUR GARAGE.

TUMBLERPOXY 2.0: storing and working temperatures of 75°-80° for the best results!

• 20-25 minute work time
• Dry to touch in 2-3 hours  depending on room temperature
• 1:1 RATIO
• 400-to-500-degree heat resistant
• FDA Compliant when fully cured for a minimum of 72 hours!

⭐️All of our epoxies are proudly made right here in the USA! 🇺🇸⭐️

 **TUMBLER DIRECTIONS**

MEASURE 1:1 RATIO

MIX TUMBLERPOXY 2.0 FOR 4-6 mins. because 2.0 is SUPER THICK AND NEEDS A LONGER MIX TIME until epoxy is clear. Mixing slow or in colder environments, will require the epoxy needing to be stirred longer. In order to get non-tacky cups every time, make sure there’s no ceiling fans, heaters, dehumidifiers, floor fans, etc. blowing on your wet epoxy. Air flowing directly on your wet epoxy will not allow our epoxy to heat up like it needs to to dry properly. This is a faster setting epoxy, so it needs to heat up quickly. Make sure epoxy is stored at 75°-80°F and work room is same temperatures for best results. Thick epoxies need to be used in hotter temps to thin them out and for them to dry properly.

Apply immediately 

Use gloved finger to work bubbles out before reaching for any heat, if done properly you’ll need little to no heat.

Once layer is to your liking hit with heat one to two rotations.

If working from a bigger batch of epoxy, make sure you’re stirring for few seconds between projects. Stuff settles and if not stirred periodically between tumblers, some tumblers will dry properly, and others won’t from the same batch.

Sand and apply next layer as early as 2-3 hours but depending on room temperature, or applying decals, vinyl, etc., you may have to wait 8 hours.

**MOLD DIRECTIONS**

Mold pieces will be rock hard at 5 hours drying in the mold. Remove from mold and allow to finish curing on a flat surface for 3-5 days. If mold pieces don’t harden up after 5 hours and remain bendy, either measurements were off, mixture wasn’t stirred long enough or coloring to epoxy ratio of 10% or less wasn’t followed...chemical reaction between part A and Part B was interrupted.

MEASURE 1:1 ratio

Mix SLOWLY for 4-5 mins. (or longer if epoxy or room temperature is colder than 72-75°F) Or until epoxy is clear with no strings or fogginess. 

Add coloring/glitter (remember coloring to epoxy ratio of 10% or less to not mess up chemical reaction and cause molds to always be bendy or the need to allow them to cure longer to get hard)

(CLEAR MOLDS: TUMBLERPOXY 2.0 is not recommended because of its thick consistency. Glitter molds are ok. Swiftpoxy works best for clear molds, much thinner consistency.) 

Mix 3 minutes, SLOWLY, add coloring to mixed epoxy, then pour into silicone mold, then allow bubbles to rise to the top 5-8 mins. before spritzing with alcohol.

(Spritz top of mold pieces with alcohol as heat will break down silicone molds quickly and eventually.)

*QUICK TIPS*

Must mix 4-5 mins. or until epoxy is clear. 

Work time 20-25 mins

Dry to touch in 2-3 hours depending on room temperature 

CAN APPLY ANOTHER LAYER between 2-3 hours IF you’re 100% sure you measured and mixed properly. Bottom layer at this point will be tacky. Ideally, you want to either sand or apply next layer when bottom layer is tacky to ensure both layers create a chemical or mechanical bond. This helps with durability if tumbler is accidentally dropped.

ALLOW TO CURE a minimum of 72 hours after last layer in-order to meet the FDA Compliancy Standards of being food safe.

**If Tumbler layer is tacky after 5 hours either TUMBLERPOXY 2.0 wasn’t measured properly, work room temperature was below 75°-80°F, or it wasn’t stirred a full minimum of 3 mins. 

Work and storing temperatures:

75°-80°F

**Hotter temps will cause TUMBLERPOXY 2.0 to dry faster, colder temps will cause TUMBLERPOXY 2.0 to dry slower. **

Opened (heat seal under lid popped) TUMBLERPOXY 2.0 will work properly for less than a year. Purchase GLAD brand Press ‘n Seal (not plastic wrap) cover tops of bottles and put lids back on to preserve your epoxy longer.

Unopened TUMBLERPOXY 2.0 stored at recommended storing temps won't expire for a year

***NO REFUNDS AND NO RETURNS. Please refer to our return policy located at the bottom of this website.

PLEASE CONSIDER PURCHASING THE EXTRA ROUTE SHIPPING INSURANCE WE OFFER TO GUARANTEE IF ORDER IS LOST OR DAMAGED, ORDER WILL BE REPLACED QUICKLY.***

 Caution: Eye and Skin irritant. Do not swallow. Do not get in eyes. Do not get on skin or clothing. Do not breathe fumes. Use proper PPE at all times. KEEP OUT OF REACH OF CHILDREN.